mima-tools

MiMa specification

General

In the following sections, <a> means "the value at the address a". In the case of <<a>>, bits 19-0 of <a> are interpreted as the address.

The MiMa uses words of 24 bits and addresses of 20 bits.

Each step, the MiMa fetches the value at the address stored in the IAR, interprets it as an instruction and executes it. If the instruction does not explicitly modify the IAR, the IAR it is incremented by one automatically.

During execution, the following situations can be encountered where execution should not be continued:

• The HALT instruction was executed
• The value at <IAR> cannot be decoded to a valid instruction
• The IAR is 0xFFFFF and an instruction was executed that did not modify the IAR

In these cases, a MiMa emulator should stop execution and show a suitable error message explaining why execution could not continue.

Instructions

An instruction has one of the following forms:

Small opcode:
+----+ +-----------------------+
| SO | |         Value/Address |
+----+ +-----------------------+
23  20 19                      0

Large opcode:
+----+ +----+ +----------------+
|  F | | LO | |          Value |
+----+ +----+ +----------------+
23  20 19  16 15               0

Small opcodes can range from 0 to E and have an address or 20-bit value as argument. Large opcodes can range from F0 to FF and have, if at all, a 16-bit value as argument.

For large opcodes without an argument, the 16 value bits are ignored. They don't have to be set to 0.

Registers

Name	Size (bits)	Function
IAR	20	Instruction Address Register
ACC	24	Accumulator
RA	20	Return Address
SP	20	Stack Pointer
FP	20	Frame Pointer

Opcodes

Opcode	Name	Function
0	LDC c (load constant)	c -> ACC
1	LDV a (load value)	<a> -> ACC
2	STV a (store value)	ACC -> <a>
3	ADD a	ACC + <a> -> ACC
4	AND a	ACC and <a> -> ACC
5	OR a	ACC or <a> -> ACC
6	XOR a	ACC xor <a> -> ACC
7	EQL a (equal)	(ACC == <a> ? -1 : 0) -> ACC
8	JMP a (jump)	a -> IAR
9	JMN a (jump if negative)	if (ACC < 0) {a -> IAR}
A	LDIV a (load indirect value)	<<a>> -> ACC
B	STIV a (store indirect value)	ACC -> <<a>>
C	CALL a	IAR -> RA; JMP a
D	LDVR d (load value with relative offset)	<SP + d> -> ACC
E	STVR d (store value with relative offset)	ACC -> <SP + d>
F0	HALT	Halt execution
F1	NOT	not ACC -> ACC
F2	RAR (rotate ACC right)	ACC >> 1 -> ACC
F3	RET (return)	RA -> IAR
F4	LDRA (load from RA)	RA -> ACC
F5	STRA (store to RA)	ACC -> RA
F6	LDSP (load from SP)	SP -> ACC
F7	STSP (store to SP)	ACC -> SP
F8	LDFP (load from FP)	FP -> ACC
F9	STFP (store to FP)	ACC -> FP
FA	ADC c (add constant)	ACC + c -> ACC

• LDC c sets bits 23-20 of ACC to 0.
• ADD a, AND a, OR a, XOR a and NOT are bitwise operations
• RAR shifts all bits in the ACC right by one. The rightmost bit wraps around to the leftmost position.
• ADC c interprets bits 15-0 as a signed integer, whose value is then added to the ACC's current value.

File format

All tools share a common file format with extension .mima. It contains the whole execution state of a MiMa, meaning the contents of its memory and all its registers.

The file is split up into blocks of 3 bytes, which form MiMa words. The bytes within a word are ordered from most to least significant.

The values of registers which are only 20 bits long are stored in the lower 20 bits of a MiMa word, and the remaining bits 23-20 are filled with zeroes, like so:

+----+ +-----------------------+
|  0 | | 20-bit register value |
+----+ +-----------------------+
23  20 19                      0

The registers and memory are stored as follows:

Word	Content
0	IAR
1	ACC
2	RA
3	SP
4	FP
starting at 6	Memory dump

The memory dump contains the words of the MiMa's memory, written in increasing order directly one after the other with nothing in-between. The dump always starts at address 0x00000, but may end before it reaches address 0xFFFFF. When reading a dump, all unspecified values are to be intialized as 0x000000.

A .mima file must always be a multiple of 3 bytes long. It must always be at least 15 bytes long (contains all register values).

Programs

mima-run

This program can load and run .mima files.

It currently does not follow the specification above.

$ mima-run --help
Usage: mima-run INFILE [-n|--steps N] [-d|--dump OUTFILE] [-q|--quiet]
                [-s|--sparse] [-r|--norun]

Available options:
  -h,--help                Show this help text
  INFILE                   The binary memory dump to load and execute
  -n,--steps N             How many instructions to execute (if not specified,
                           runs until HALT or execution exception)
  -d,--dump OUTFILE        If specified, write the MiMa's binary memory dump to
                           this file after execution is finished
  -q,--quiet               Don't print the memory dump
  -s,--sparse              Don't print memory locations containing only 0x000000
                           in the memory dump
  -r,--norun               Don't run the MiMa. Use the initial state for all
                           further actions

Conventions

In the source code, the name MiMa is spelled Mima. When displayed, it is spelled MiMa.

Executable names are all lowercase, and words are separated by a -.